SHOP PRICES
Effective August 29, 2008 Prices are subject to change
| Head Work | ||
1001 |
Disassemble and clean |
$28.00 |
1002 |
Glass bead, each |
$32.00 |
1003 |
Magnaflux, each |
$28.00 |
1004 |
Pressure test head, each |
$28.00 |
1005 |
Install valve guide and hone, each |
$9.00 |
| 1005A | Intstall valve guide and hone, set of 16 |
$112.00 |
| 1005B | Install bronzewall valve guide & hone to fit, ea. |
$9.00 |
| 1005C | Install bronzewall valve guide & hone to fit, set of 16 |
$112.00 |
1006 |
Machine guides for seal, each |
$2.25 |
| 1006A | Machine for seals and spring pad (1 set up) |
$52.00 |
1007 |
Valve job, standard, per cylinder |
$20.50 |
1008 |
CC combustion chamber, each |
$20.00 |
1009 |
Match port head to intake |
$100.00 |
1010 |
Mill intake surface flat up to |
$20.00 |
.020, each |
||
| 1010A | Mill Intake Surface Flat over .020 |
$28.00 |
1011 |
Mill intake surface angle, each |
$35.00 |
1012 |
Install valve seat, each |
$12.00 |
1013 |
Machine for oversize valve |
$8.00 |
1014 |
Valve job race per cylinder, includes cleaning |
$30.00 |
1015 |
Set valve spring pressure, each |
$3.00 |
1016 |
Mill head up to .020 |
$30.00 |
1017 |
Mill head over .020 |
$40.00 |
| 1017A | Angle mill head up to .100 with intake side corrected & spot face head bolt holes, each | $100.00 |
| 1017B | Angle mill head over .100 with intake side corrected & spot face head bolt holes, each | $120.00 |
1018 |
Machine spring pads, each |
$2.50 |
1019 |
Clean, check, lap valves & assy |
$40.00 |
| 1020 | O-Ring cylinder (w/ .041" SS wire) each | $18.00 |
| 1020A | Machine .041" groove in head as receiver | $96.00 |
| V8 pr. | ||
| 1021 | Machine receiver groove for Fel-Pro gasket | $120.00 |
| V-8 pair heads | ||
| 1022 | Machine stem holes in SBC 400 heads | $60.00 |
| Intake Work | ||
1200 |
Glass bead |
$30.00 |
1201 |
Mill intake V8 |
$70.00 |
1202 |
Match port |
$100.00 |
| Piston Work | ||
2000 |
R&R Pistons floated (each) |
$3.00 |
2001 |
Press off piston, each |
$3.00 |
2002 |
Press on piston, each |
$3.00 |
2003 |
Glass bead, each |
$6.00 |
2004 |
CC dome, each |
$15.00 |
2005 |
Fit dome to head, each |
$12.00 |
2006 |
Fit pin, each |
$5.00 |
2007 |
Flycut intake valve reliefs, each |
$6.00 |
2008 |
Flycut exhaust valve reliefs, each |
$6.00 |
| 2009 | Cut piston domes to flattops, ea. |
$12.50 |
| 2009A | Cut piston domes to specs, each |
$9.50 |
| Rod Work | ||
3001 |
Magnaflux, each |
$6.00 |
3002 |
Glass bead, each |
$8.00 |
3003 |
Recondition rod big end, each |
$16.00 |
| 3003A | Recondition rod big end, set of 8 |
$96.00 |
3004 |
Install and pin fit bushing, each |
$20.00 |
| 3004A | Install Bushings & pin fit (set-8) |
$120.00 |
3005 |
Pin fit bushing, each |
$5.00 |
3006 |
Cut side clearance, each |
$2.50 |
3007 |
Polish beams, each |
$20.00 |
3008 |
Check & Clean Rods, each |
$4.00 |
| Balancing | ||
4001 |
Balance engine assy, stock V8 |
$175.00 |
4002 |
Balance engine assy, race V8 |
$200.00 |
| 4002A | Turn counterweights for balancing V8 |
$75.00 |
4003 |
Crank only 4, 6, or V8 |
$95.00 |
4004 |
Internal balance with heavy metal V8 (add up to 4 pcs. plus heavy metal per piece) |
$275 & up |
| Block Work | ||
5001 |
Vat and clean block |
$45.00 |
5002 |
Magnaflux |
$45.00 |
5003 |
Sonic test |
$80.00 |
5004 |
Cut for rod clearance |
$60.00 |
5005 |
Pressure check block |
$45.00 |
5006 |
Bore, up to .040 V8 |
$80.00 |
5007 |
Bore, each add'l .040 |
$80.00 |
5008 |
Hone for the street |
$85.00 |
5009 |
Race prep SBC to 3.625 | $100.00 |
| 5009A | Race prep SBC to 3.750 stroke & up |
$130.00 |
| 5009B | Race prep BBC to 4.250 |
$100.00 |
| 5009C | Race prep BBC to 4.375 |
$130.00 |
| 5009D | Race prep BBC from 4.375 |
$160.00 |
| 5009E | Race prep BBM to 4.250 | $125.00 |
5010 |
Hone block new bore with torque plates | $160.00 |
5010A |
Clean up hone for new rings |
$90.00 |
with plates |
||
5010B |
Clean up hone for new rings |
$55.00 |
without plates |
||
| 5010C | Hone Block new bore, no plates | $110.00 |
5011 |
Install cam bearings |
$35.00 |
(doesn't include parts) |
||
| 5011A | lInstall cam bearings & fit as nec. | $55.00 |
5012 |
Check align bore |
$24.00 |
5013 |
Align bore |
$125.00 |
5014 |
Align hone |
$125.00 |
| 5014A | Align hone & fit for new caps | $170.00 |
5015 |
Align hone with 4 bolt mains |
$140.00 |
5016 |
Align hone with main studs |
$155.00 |
5017 |
Install 4 bolt main caps |
$250.00 |
5018 |
Mill, deck up to .020 |
$75.00 |
| 5018A | Mill block end rails |
$35.00 |
5019 |
Mill, deck over .020 |
$95.00 |
| 5019A | Mill block rails for intake | $60.00 |
5020 |
O-ring (with .041 SS wire) V8 |
$136.00 |
| 5020A | Install .041" SS Wire in premachined grooves | $48.00 |
5021 |
Sleeve cylinder, each |
$55.00 |
(doesn't include parts) |
||
5022 |
Pour block with hard block |
$125.00 |
| (doesn't include parts) | ||
| 5023 | Align bore cam tunnel repair | $175.00 |
5024 |
Bore cam tunnel for BBC (brg) |
$200.00 |
5025 |
Bore cam tunnel (roller brg) |
$370.00 |
| 5025A | Machine oil groove in cam tunnel | $50.00 |
5026 |
Install freeze plug kit |
$16.00 |
| 5027 | Bush lifter bores BBM plus bushings | $400.00 |
| 5028 | Bush lifter bores SBC plus bushings | $350.00 |
| 5029 | Bush lifter bores BBC plus bushings | $400.00 |
| Engine Work | ||
6001 |
Disassemble, check and clean |
$150.00 |
6002 |
Check deck height |
$35.00 |
6003 |
Check piston to valve clearance |
$45.00 |
6004 |
Check compression ratio |
$45.00 |
6005 |
Degree cam |
$60.00 |
6006 |
File fit rings, set |
$40.00 |
6007 |
Measure bearings clearance, mains | $45.00 |
6008 |
Measure bearings clearance, rods |
$45.00 |
6009 |
Assemble engine, complete |
$550.00 |
(ring fit and all clearances checked) |
||
6010 |
Assemble short block, only V8 |
$225.00 |
6011 |
Assemble short block with cam & cover & degree |
$275.00 |
| 6012 | Check & set pushrod length |
$35.00 |
| 6013 | Check & clean engine parts |
$60.00 |
(min $30.00) |
||
| Crank Work | ||
7000 |
Clean crank |
$20.00 |
7001 |
Magnaflux crankshaft |
$38.00 |
| 7001A | Magnaflux main bearing caps (each) |
$3.00 |
7002 |
Polish only crankshaft |
$30.00 |
7003 |
Grind, polish, clean |
$98.00 |
7004 |
Chamfer oil holes |
$24.00 |
7005 |
Deburr (Mopar only) |
$25.00 |
| Transmission Work | ||
8001 |
Tear down |
$35.00 |
8002 |
Clean |
$75.00 |
| 8003 | Rebuild PG | $200.00 |
8004 |
Rebuild PG complete, race |
$250.00 |
8005 |
Freshen, PS PG tranny |
$150.00 |
8006 |
Build front pump PG |
$45.00 |
| 8007 | Build Race 727 Torqueflite (already in) |
$300.00 |
| 8008 | Build PG Trans. Complete | $400.00 |
| Rearend Work | ||
9001 |
Tear down |
$35.00 |
9002 |
Clean |
$75.00 |
9003 |
Setup Dana, out of car |
$200.00 |
9004 |
Set up 8 3/4, out of car |
$175.00 |
| 9004A | Set up 9" Ford, out of car | $175.00 |
9005 |
Set up 12 bolt Chevrolet, out of car |
$200.00 |
9006 |
Install posi-unit |
$100.00 |
9007 |
Install all bearings |
$95.00 |
9008 |
Install axle bearings, |
$22.00 |
standard or race, each |
||
9009 |
Shorten housing |
$150.00 |
9010 |
Install spring pads |
$45.00 |
9011 |
Sand blast housing |
$50.00 |
9012 |
Slick shift Dana carrier bearings |
$40.00 |
| Flow Bench Work | ||
9100 |
Flow (1) cylinder I&E |
$90.00 |
| Miscellaneous | ||
| 9400 | Misc. labor per hr. (min. 1/4 hr.) |
$60.00 |
| 9401 | Fill 10 oz. air bottle |
$5.00 |
9501 |
Shop labor, hour (min. 1/2 hr.) |
$60.00 |
9502 |
Welding, hour (min 1/2 hr.) |
$60.00 |
9503 |
Helicoil bolt hole, each |
$5.50 |
| 9503A | 2 or more |
$5.00 |
9504 |
Glass beading, hour |
$50.00 |
| Dyno | ||
9505 |
Dyno session |
$400.00 |
9506 |
Dyno day session |
$550.00 |
9507 |
Dyno special session (per hour) |
$75.00 |